Advanced Search
| Title | Publication | Publish Year |
|---|---|---|
|
Flame-Spread Measurements By the Radiant Panel Flame-Spread Method
The radiant-panel flame-spread test method indicated that variations in moisture content and mean density can cause appreciable differences in results from the same materials. At the same mean density and […]
|
Forest Products Journal | 1960 |
|
Forced Air Drying Sweet Gum Furniture Billets in Solid Stacks
Green sap gum furniture billets, 2-1/4 inches in diameter and 3 inches long, were dried in solid stacks in portable cradles. The technique increased dryer capacity and simplified handling while […]
|
Forest Products Journal | 1965 |
|
Four-Inch Southern Pine Lumber; Seasoning Factors for Modulus of Elasticity and Modulus of Rupture
The objective of this study was to evaluate the changes in bending properties of 4-inch-thick beams of southern pine when dried to 12 percent moisture content, and to relate these […]
|
Forest Products Journal | 1968 |
|
FPRS Annual Review . . . Developments in Wood Drying
Raising of the minimum wage rate to $1.25 per hour and the new proposed moisture content and size standards in 1963 have made a considerable impact on the wood drying […]
|
Forest Products Journal | 1964 |
|
FPRS Annual Review of Wood Drying
Prepared under the auspices of the FPRS, Wood Drying Division, this review of 143 articles presents a current bibliography of new developments in the field of wood drying. In the […]
|
Forest Products Journal | 1968 |
|
Friction in Wood Cutting
This paper discusses a recent investigation in which friction coefficients were measured using special apparatus on the effects of variables, such as pressure, contact area, sliding speed, surface roughness of […]
|
Forest Products Journal | 1967 |
|
Fuel Values of Chemically Deadened White Oak and Basswood Trees
The use of wood as a commercial and domestic energy source is receiving increased attention. The useable fuel value of wood varies with its moisture content and specific gravity. Past […]
|
Forest Products Journal | 1980 |
|
Fundamentals of flakeboard manufacture: internal-mat conditions
Real-time measurements were made of temperature, gas pressure, and compaction pressure in the face and core regions of flakeboard panels during manufacture. Data from the manufacture of 24 yellow-poplar flakeboard […]
|
Forest Products Journal | 1988 |
|
Furnish moisture content, resin nonvolatile content, and assembly time effects on properties of mixed hardwood strandboard
The objective of this research was to investigate the effects of three levels each of furnish moisture content (MC) (2%, 5%, 8%), resin nonvolatile content (50.8%, 54.8%, 58.8%), and assembly […]
|
Forest Products Journal | 1988 |
|
Gas pressure and temperature in the mat during flakeboard manufacture
Local internal-mat conditions of temperature, moisture content, gas pressure, and stress history interact to affect adhesive cure, wood densification, and the subsequent panel properties. Data is presented to illustrate the […]
|
Forest Products Journal | 1988 |
|
Gelatin Encapsulation of Methylisothiocyanate for Control of Wood Decay Fungi
Encapsulation of the fumigant methylisothiocyanate (MIT) in gelatin was studied as an alternative to liquid fumigant treatments for control of decay fungi in wooden utility poles. Gelatin-encapsulated MIT was stored […]
|
Forest Products Journal | 1985 |
|
GIS mapping of monthly outdoor and indoor equilibrium moisture content for the United States
Geographic information system (GIS) maps of monthly outdoor equilibrium moisture content (EMC) of wood in the contiguous United States were prepared from the 1961 to 1990 Global Climate Normals of […]
|
Forest Products Journal | 2004 |
|
Gluability of Southern Pine Earlywood and Latewood
Glue-bond quality, as tested wet and dry in tension, was best with earlywood to earlywood and poorest with latewood to latewood; earlywood to latewood was intermediate. Optimum closed assembly, time […]
|
Forest Products Journal | 1968 |
|
Gluing of Furniture Parts
To sucessfully glue furniture, many factors have to be controlled. In the Drexel Furniture Co. plants, all employees involved with gluing attend training programs on the subject, followed by on-the-job […]
|
Forest Products Journal | 1954 |
|
Green Sorting Incense-Cedar for Increased Air-Drying Yard Throughput
This study was aimed at determining the variability in drying rates and times of suspected different sorts (classifications) of incense-cedar, and whether drying time could be predicted by the drying […]
|
Forest Products Journal | 1984 |
|
Green Southern Yellow Pine Veneer–Saturation Principle of Moisture Measure to Establish Drying Sorts
Visual sorting of southern yellow pines which is pre dominately sapwood, has not been practical. The southern pine plywood industry is faced with drying veneer that is highly variable in […]
|
Forest Products Journal | 1970 |
|
Gross Heat of Combustion of Five Hardwood Species At Differing Moisture Contents
The heat of combustion was determined for samples of some Northeastern hardwood sawdusts and yellow poplar bark. Oven dry material was wetted to obtain a range of moisture contents up […]
|
Forest Products Journal | 1974 |
|
Growth stress versus capillary tension in relation to trunk splitting in Fraser fir Christmas trees
A study was conducted to determine why some harvested Fraser fir (Abies fraseri (Pursh) Poir.) Christmas trees develop longitudinal splits on the lower portion of the trunk (butt), typically beginning […]
|
Forest Products Journal | 1993 |
|
Growth stress versus capillary tension in relation to trunk splitting in Fraser fir Christmas trees
A study was conducted to determine why some harvested Fraser fir (Abies fraseri (Pursh) Poir.) Christmas trees develop longitudinal splits on the lower portion of the trunk (butt), typically beginning […]
|
Forest Products Journal | 1993 |
|
Hardboard Stiffness and Tensile Strength Over a Moisture and Temperature Range Simulating Exterior Use
The effects of a range of moisture contents (MCs) from zero to 20 percent and of temperatures from -15? to ?C on the tensile properties of a wet-process heat treated […]
|
Forest Products Journal | 1983 |
| Hardwood Symposium Proceedings | 1982 | |
|
High Speed Production of Flooring
A brief description of an oak flooring operation is given, followed by an explanation of the difference between a normal flooring operation and a high-speed operation. The majority of flooring […]
|
Forest Products Journal | 1953 |
|
High Temperature Drying of British Columbia Softwoods
A high-temperature kiln of 100 bd. ft. capacity has been built for the Canadian Forest Products Laboratory. Air velocity can be maintained between 400 and 1100 feet per minute and […]
|
Forest Products Journal | 1957 |
|
High-Temperature and Conventional Temperature Methods for Drying Lodgepole Pine and Western Larch Studs
Commercial kilns were used to dry both species using conventional schedules or a high (240? – 235?F) dry bulb. Kiln parameters are described along with procedures for the study in […]
|
Forest Products Journal | 1967 |
|
High-Temperature Kiln-Drying of 4/4 Lumber from 12 Hardwood Species
One-inch lumber of 12 hardwood species was kiln-dried by two schedules: 1) 230?F on stock green from the saw to 6 to 8 percent moisture content (MC) in 50 to […]
|
Forest Products Journal | 1984 |