Advanced Search
| Title | Publication | Publish Year |
|---|---|---|
|
Warp Reduction in Kiln-Drying Hardwood Dimension
The occurrence of crook, twist, and cup in lumber can cause major yield losses, discourage utilization of warp-prone lumber from small-diameter trees, and prevent use of more efficient processing methods. […]
|
Forest Products Journal | 1982 |
|
Warp Reduction in Young-Growth Ponderosa Pine Studs Dried By Different Methods with Top-Load Restraint
Studs sawed from small diameter, young-growth ponderosa pine suffer severe warp when dried. The feasibility of using a top load restraint of 200 pounds per square foot during drying was […]
|
Forest Products Journal | 1978 |
|
Warp reduction of red pine two-by-fours via restrained drying
Warp in 2 by 4 lumber is a significant cause of loss in grade and value. Crook and twist are two of the largest factors. The softwood lumber grading standards […]
|
Forest Products Journal | 2005 |
|
Warp reduction of SYP lumber by restrained drying
Warp in dimension lumber is a significant cause for loss in grade and value. Among dimension lumber, the 2- by 4-inch size is typically the most susceptible to warp for […]
|
Forest Products Journal | 2005 |
|
Western wood species treated with chromated copper arsenate: effect of moisture content
The effect of wood moisture content on treatability with chromated copper arsenate was examined for western hemlock, mountain hemlock, grand fir, white fir, noble fir, Pacific silver fir, and Douglas-fir […]
|
Forest Products Journal | 1996 |
|
Within-Kiln Variability of Transmission Heat Losses
Transmission heat losses from an aluminum sandwich wall research kiln were measured using a thermal flux sensor to determine the causes of within-kiln variability in transmissional heat losses. Considerable differences […]
|
Forest Products Journal | 1984 |
|
Wood and drying properties of white oak from thinned and unthinned plantations
The objective of this study was to examine selected wood and drying properties of white oak (Quercus alba L.) trees removed from plantations in southern Illinois. Trees from two stands, […]
|
Forest Products Journal | 1991 |
|
Wood color control during kiln drying
The coloration of wood during drying in a laboratory kiln was investigated and modelled using multivariate techniques: principal component analysis and partial least squares (PLS). The wood species included were […]
|
Forest Products Journal | 2002 |
|
Wood Drying Review
This review is mainly concerned with drying of thin as veneer, chips, and particle drying for the year 1969. Recent research in jet drying, microwave combined with jet drying, pre-frozen […]
|
Forest Products Journal | 1970 |
|
Wood Drying Review–1970
This review of wood drying techniques reports new developments in reducing air-drying time, high temperature drying, use of combined schedules, drying presurfaced oak, segregation of wet stock, dynamic transverse compression, […]
|
Forest Products Journal | 1972 |
|
Wood Seasoning Bibliography, 1956-7
A total of 224 titles were selected from United States Department of Agriculture Library, Bibliography of Agriculture 1957 and 1958 (except December), Forestry Abstracts 1957 and 1958, and Russian Accessions, […]
|
Forest Products Journal | 1959 |
|
Wooden Boxes and Crates
Even though box and crate products allow more efficient use of lower grades of lumber and scrap, some standardization of board sizes must be used to permit economic conversion into […]
|
Forest Products Journal | 1956 |
|
X-Ray Used in Drying Studies to Detect Honeycomb
Honeycomb is an internal separation of wood fibers, usually along wood rays, that occurs in lumber and other wood products during the course of drying. If dry-bulb temperatures are too […]
|
Forest Products Journal | 1970 |
|
Xerographic Copies of Stress Sections Can Improve Drying Records
Xerographic reproduction was used to provide permanent records of stress development in drying wood. Images of prong test samples taken during all phases of stress evaluation record the interacting effects […]
|
Forest Products Journal | 1979 |
|
Yield Comparisons Between 4/4 Lumber and SDR Studs from Small Woods-Run Yellow-Poplar Logs
A surplus of standing yellow-poplar in the pole to small sawlog size is available for use in the Eastern United States. Formerly, material such as this was used for furniture […]
|
Forest Products Journal | 1981 |
|
Yields of Unexposed Oak Dimension Parts from Lumber Planed Before vs. After Drying By Radio-Frequency Vacuum Or Dehumidification Methods
A study was conducted to determine the effects of planing of lumber before versus after drying on the yield of sound, unexposed dimension cuttings from short oak lumber dried by […]
|
Forest Products Journal | 1985 |
|
Young-Growth Douglas-Fir: Is It Predisposed to Warp?
Approximately one hundred 8-foot, rough, green studs were randomly selected from 2-by 4-inch young-growth Douglas-fir (Pseudotsuga taxifolia Britt.) lumber at each of 20 western Oregon sawmills. One sample of 99 […]
|
Forest Products Journal | 1955 |
|
Zinc Naphthenate Pressure Treatment of Pine Logs for Log Homes
This study was designed to determine the feasibility of treating log-home logs with water-dispersible zinc naphthenate (ZWD). Variables included: 1) species (southern pine, lodgepole pine), 2) conditioning method (kiln-drying, high-temperature […]
|
Forest Products Journal | 1986 |